Wufiwiki - Benutzerbeiträge [de]

Plus talk:DialogBuildingWizard

2008-08-14T02:47:55Z

Cmitterer: Die Seite wurde neu angelegt: What is the hight of a store exactly? Including ceiling/floor or excluding? How is the hygrothermal capacity of the ceiling/floor in a multi-store building calculated?

What is the hight of a store exactly? Including ceiling/floor or excluding? How is the hygrothermal capacity of the ceiling/floor in a multi-store building calculated?

Discussion:Main

2008-08-07T05:27:56Z

Cmitterer: /* Christoph's annotation */

Please make sure, that the user is '''NOT''' the problem. After that proceed with the following:

== WUFI 1D Pro ==

hmm...

== WUFI 2D ==

haa...

== WUFI-Plus ==

=== Bugs ===
* Two graphs are shown on one page. If the date-axis is changed on the above graph, the second graph is then different - but only one x-axis label is available.
* Sometimes window can not be minimized

=== Problems ===

* By use of "Assign from Database" the setup is overridden without asking (asking happens only if "Edit" is used.
* How do I create a monopitch roof?
* Is the A/V ratio based on the internal or the external dimensions?
* How is the exterior climate data interpolated with shorter timesteps than available in the climate file? How big is the difference of simulations with hourly values and shorter timesteps?
* How are the ventilation control mechanisms exactly?
* How do I model groundwater? (I can only specify 100% RH but no fluid water on the surface)

=== Wishlist ===

* Time-dependent shading
* Specified saving options (without results, with general results, with results for each component) on one page, not seperately for each component
* Calculation results: Please add surface area in the component information part
* Differentiation between forced and natural air exchange (with possibility to read file)
* Preview of the created building in the building wizard
* Define standard dimensions of windows with frame reduction factor and adapt frame reduction factor with changing window dimensions
* Start "Calc Wufi" from header-dialog
* Delete "new case" button
* Give choice if one wants to copy windows for every storey in a multi-storey building
* Batch mode for WUFI Plus with automatic results file generation
* Possibility to read each boundary condition from file
* Save project without results

=== Christoph's annotation ===

----

==== Smaller Problems ====
=====''' Distribution of solar gains on inner surfaces'''=====
How is the behavior?
If ''Other_Parameters'' "Proportional to area", 100% of solar gains will distributed proportional to the components, or 100% less the ratio of "Solar radiation direct to inner Air"?

In the case of "Proportional to area" in ''Components -> Numerics'' "Solar radiation on inner surfaces[%]" shows the percentage [1...100] in an inactive box. But if "user defined" you must not input a number between [1...100], but between [0...1].

[[Bild:Screenshot_-_07.08.2008_,_12_24_00.png|siehe]]

Discussion:Main

2008-08-07T05:27:12Z

Cmitterer: /* Smaller Problems */

Please make sure, that the user is '''NOT''' the problem. After that proceed with the following:

== WUFI 1D Pro ==

hmm...

== WUFI 2D ==

haa...

== WUFI-Plus ==

=== Bugs ===
* Two graphs are shown on one page. If the date-axis is changed on the above graph, the second graph is then different - but only one x-axis label is available.
* Sometimes window can not be minimized

=== Problems ===

* By use of "Assign from Database" the setup is overridden without asking (asking happens only if "Edit" is used.
* How do I create a monopitch roof?
* Is the A/V ratio based on the internal or the external dimensions?
* How is the exterior climate data interpolated with shorter timesteps than available in the climate file? How big is the difference of simulations with hourly values and shorter timesteps?
* How are the ventilation control mechanisms exactly?
* How do I model groundwater? (I can only specify 100% RH but no fluid water on the surface)

=== Wishlist ===

* Time-dependent shading
* Specified saving options (without results, with general results, with results for each component) on one page, not seperately for each component
* Calculation results: Please add surface area in the component information part
* Differentiation between forced and natural air exchange (with possibility to read file)
* Preview of the created building in the building wizard
* Define standard dimensions of windows with frame reduction factor and adapt frame reduction factor with changing window dimensions
* Start "Calc Wufi" from header-dialog
* Delete "new case" button
* Give choice if one wants to copy windows for every storey in a multi-storey building
* Batch mode for WUFI Plus with automatic results file generation
* Possibility to read each boundary condition from file
* Save project without results

=== Christoph's annotation ===
==== Smaller Problems ====
=====''' Distribution of solar gains on inner surfaces'''=====
How is the behavior?
If ''Other_Parameters'' "Proportional to area", 100% of solar gains will distributed proportional to the components, or 100% less the ratio of "Solar radiation direct to inner Air"?

In the case of "Proportional to area" in ''Components -> Numerics'' "Solar radiation on inner surfaces[%]" shows the percentage [1...100] in an inactive box. But if "user defined" you must not input a number between [1...100], but between [0...1].

[[Bild:Screenshot_-_07.08.2008_,_12_24_00.png|siehe]]

Discussion:Main

2008-08-07T05:26:24Z

Cmitterer: /* Smaller Problems */

Please make sure, that the user is '''NOT''' the problem. After that proceed with the following:

== WUFI 1D Pro ==

hmm...

== WUFI 2D ==

haa...

== WUFI-Plus ==

=== Bugs ===
* Two graphs are shown on one page. If the date-axis is changed on the above graph, the second graph is then different - but only one x-axis label is available.
* Sometimes window can not be minimized

=== Problems ===

* By use of "Assign from Database" the setup is overridden without asking (asking happens only if "Edit" is used.
* How do I create a monopitch roof?
* Is the A/V ratio based on the internal or the external dimensions?
* How is the exterior climate data interpolated with shorter timesteps than available in the climate file? How big is the difference of simulations with hourly values and shorter timesteps?
* How are the ventilation control mechanisms exactly?
* How do I model groundwater? (I can only specify 100% RH but no fluid water on the surface)

=== Wishlist ===

* Time-dependent shading
* Specified saving options (without results, with general results, with results for each component) on one page, not seperately for each component
* Calculation results: Please add surface area in the component information part
* Differentiation between forced and natural air exchange (with possibility to read file)
* Preview of the created building in the building wizard
* Define standard dimensions of windows with frame reduction factor and adapt frame reduction factor with changing window dimensions
* Start "Calc Wufi" from header-dialog
* Delete "new case" button
* Give choice if one wants to copy windows for every storey in a multi-storey building
* Batch mode for WUFI Plus with automatic results file generation
* Possibility to read each boundary condition from file
* Save project without results

=== Christoph's annotation ===
==== Smaller Problems ====
* ''' Distribution of solar gains on inner surfaces'''
How is the behavior?
If ''Other_Parameters'' "Proportional to area", 100% of solar gains will distributed proportional to the components, or 100% less the ratio of "Solar radiation direct to inner Air"?

In the case of "Proportional to area" in ''Components -> Numerics'' [[Bild:Screenshot_-_07.08.2008_,_12_24_00.png|siehe]] "Solar radiation on inner surfaces[%]" shows the percentage [1...100] in an inactive box. But if "user defined" you must not input a number between [1...100], but between [0...1].

[[Bild:Screenshot_-_07.08.2008_,_12_24_00.png|siehe]]

Discussion:Main

2008-08-07T05:21:17Z

Cmitterer: /* Smaller Problems */

Please make sure, that the user is '''NOT''' the problem. After that proceed with the following:

== WUFI 1D Pro ==

hmm...

== WUFI 2D ==

haa...

== WUFI-Plus ==

=== Bugs ===
* Two graphs are shown on one page. If the date-axis is changed on the above graph, the second graph is then different - but only one x-axis label is available.
* Sometimes window can not be minimized

=== Problems ===

* By use of "Assign from Database" the setup is overridden without asking (asking happens only if "Edit" is used.
* How do I create a monopitch roof?
* Is the A/V ratio based on the internal or the external dimensions?
* How is the exterior climate data interpolated with shorter timesteps than available in the climate file? How big is the difference of simulations with hourly values and shorter timesteps?
* How are the ventilation control mechanisms exactly?
* How do I model groundwater? (I can only specify 100% RH but no fluid water on the surface)

=== Wishlist ===

* Time-dependent shading
* Specified saving options (without results, with general results, with results for each component) on one page, not seperately for each component
* Calculation results: Please add surface area in the component information part
* Differentiation between forced and natural air exchange (with possibility to read file)
* Preview of the created building in the building wizard
* Define standard dimensions of windows with frame reduction factor and adapt frame reduction factor with changing window dimensions
* Start "Calc Wufi" from header-dialog
* Delete "new case" button
* Give choice if one wants to copy windows for every storey in a multi-storey building
* Batch mode for WUFI Plus with automatic results file generation
* Possibility to read each boundary condition from file
* Save project without results

=== Christoph's annotation ===
==== Smaller Problems ====
* ''' Distribution of solar gains on inner surfaces'''
How is the behavior?
If ''Other_Parameters'' "Proportional to area", 100% of solar gains will distributed proportional to the components, or 100% less the ratio of "Solar radiation direct to inner Air"?

In the case of "Proportional to area" in ''Components -> Numerics'' [[Bild:Screenshot_-_07.08.2008_,_12_24_00.png|siehe]] "Solar radiation on inner surfaces[%]" shows the percentage [1...100] in an inactive box. But if "user defined" you must not input a number between [1...100], but between [0...1].

Discussion:Main

2008-08-07T05:18:40Z

Cmitterer: /* Smaller Problems */

Please make sure, that the user is '''NOT''' the problem. After that proceed with the following:

== WUFI 1D Pro ==

hmm...

== WUFI 2D ==

haa...

== WUFI-Plus ==

=== Bugs ===
* Two graphs are shown on one page. If the date-axis is changed on the above graph, the second graph is then different - but only one x-axis label is available.
* Sometimes window can not be minimized

=== Problems ===

* By use of "Assign from Database" the setup is overridden without asking (asking happens only if "Edit" is used.
* How do I create a monopitch roof?
* Is the A/V ratio based on the internal or the external dimensions?
* How is the exterior climate data interpolated with shorter timesteps than available in the climate file? How big is the difference of simulations with hourly values and shorter timesteps?
* How are the ventilation control mechanisms exactly?
* How do I model groundwater? (I can only specify 100% RH but no fluid water on the surface)

=== Wishlist ===

* Time-dependent shading
* Specified saving options (without results, with general results, with results for each component) on one page, not seperately for each component
* Calculation results: Please add surface area in the component information part
* Differentiation between forced and natural air exchange (with possibility to read file)
* Preview of the created building in the building wizard
* Define standard dimensions of windows with frame reduction factor and adapt frame reduction factor with changing window dimensions
* Start "Calc Wufi" from header-dialog
* Delete "new case" button
* Give choice if one wants to copy windows for every storey in a multi-storey building
* Batch mode for WUFI Plus with automatic results file generation
* Possibility to read each boundary condition from file
* Save project without results

=== Christoph's annotation ===
==== Smaller Problems ====
* ''' Distribution of solar gains on inner surfaces'''
How is the behavior?
If ''Other_Parameters'' "Proportional to area", 100% of solar gains will distributed proportional to the components, or 100% less the ratio of "Solar radiation direct to inner Air"?

In the case of "Proportional to area" in ''Components -> Numerics'' [[Bild:Datei.jpg|Link-Text]] "Solar radiation on inner surfaces[%]" shows the percentage [1...100] in an inactive box. But if "user defined" you must not input a number between [1...100], but between [0...1].

Discussion:Main

2008-08-07T05:15:20Z

Cmitterer: /* Smaller Problems */

Please make sure, that the user is '''NOT''' the problem. After that proceed with the following:

== WUFI 1D Pro ==

hmm...

== WUFI 2D ==

haa...

== WUFI-Plus ==

=== Bugs ===
* Two graphs are shown on one page. If the date-axis is changed on the above graph, the second graph is then different - but only one x-axis label is available.
* Sometimes window can not be minimized

=== Problems ===

* By use of "Assign from Database" the setup is overridden without asking (asking happens only if "Edit" is used.
* How do I create a monopitch roof?
* Is the A/V ratio based on the internal or the external dimensions?
* How is the exterior climate data interpolated with shorter timesteps than available in the climate file? How big is the difference of simulations with hourly values and shorter timesteps?
* How are the ventilation control mechanisms exactly?
* How do I model groundwater? (I can only specify 100% RH but no fluid water on the surface)

=== Wishlist ===

* Time-dependent shading
* Specified saving options (without results, with general results, with results for each component) on one page, not seperately for each component
* Calculation results: Please add surface area in the component information part
* Differentiation between forced and natural air exchange (with possibility to read file)
* Preview of the created building in the building wizard
* Define standard dimensions of windows with frame reduction factor and adapt frame reduction factor with changing window dimensions
* Start "Calc Wufi" from header-dialog
* Delete "new case" button
* Give choice if one wants to copy windows for every storey in a multi-storey building
* Batch mode for WUFI Plus with automatic results file generation
* Possibility to read each boundary condition from file
* Save project without results

=== Christoph's annotation ===
==== Smaller Problems ====
* ''' Distribution of solar gains on inner surfaces'''
How is the behavior?
If ''Other_Parameters'' "Proportional to area", 100% of solar gains will distributed proportional to the components, or 100% less the ratio of "Solar radiation direct to inner Air"?

In the case of "Proportional to area" in ''Components -> Numerics'' [[[[Bild:Link-Text]]]] "Solar radiation on inner surfaces[%]" shows the percentage [1...100] in an inactive box. But if "user defined" you must not input a number between [1...100], but between [0...1].

Datei:Beispiel.jpg

2008-08-07T05:12:42Z

Cmitterer:

Discussion:Main

2008-08-07T05:11:32Z

Cmitterer: /* Smaller Problems */

Please make sure, that the user is '''NOT''' the problem. After that proceed with the following:

== WUFI 1D Pro ==

hmm...

== WUFI 2D ==

haa...

== WUFI-Plus ==

=== Bugs ===
* Two graphs are shown on one page. If the date-axis is changed on the above graph, the second graph is then different - but only one x-axis label is available.
* Sometimes window can not be minimized

=== Problems ===

* By use of "Assign from Database" the setup is overridden without asking (asking happens only if "Edit" is used.
* How do I create a monopitch roof?
* Is the A/V ratio based on the internal or the external dimensions?
* How is the exterior climate data interpolated with shorter timesteps than available in the climate file? How big is the difference of simulations with hourly values and shorter timesteps?
* How are the ventilation control mechanisms exactly?
* How do I model groundwater? (I can only specify 100% RH but no fluid water on the surface)

=== Wishlist ===

* Time-dependent shading
* Specified saving options (without results, with general results, with results for each component) on one page, not seperately for each component
* Calculation results: Please add surface area in the component information part
* Differentiation between forced and natural air exchange (with possibility to read file)
* Preview of the created building in the building wizard
* Define standard dimensions of windows with frame reduction factor and adapt frame reduction factor with changing window dimensions
* Start "Calc Wufi" from header-dialog
* Delete "new case" button
* Give choice if one wants to copy windows for every storey in a multi-storey building
* Batch mode for WUFI Plus with automatic results file generation
* Possibility to read each boundary condition from file
* Save project without results

=== Christoph's annotation ===
==== Smaller Problems ====
* ''' Distribution of solar gains on inner surfaces'''
How is the behavior?
If ''Other_Parameters'' "Proportional to area", 100% of solar gains will distributed proportional to the components, or 100% less the ratio of "Solar radiation direct to inner Air"?

In the case of "Proportional to area" in ''Components -> Numerics''[[Bild:Beispiel.jpg]] "Solar radiation on inner surfaces[%]" shows the percentage [1...100] in an inactive box. But if "user defined" you must not input a number between [1...100], but between [0...1].

Discussion:Main

2008-08-07T05:08:23Z

Cmitterer: /* Smaller Problems */

Please make sure, that the user is '''NOT''' the problem. After that proceed with the following:

== WUFI 1D Pro ==

hmm...

== WUFI 2D ==

haa...

== WUFI-Plus ==

=== Bugs ===
* Two graphs are shown on one page. If the date-axis is changed on the above graph, the second graph is then different - but only one x-axis label is available.
* Sometimes window can not be minimized

=== Problems ===

* By use of "Assign from Database" the setup is overridden without asking (asking happens only if "Edit" is used.
* How do I create a monopitch roof?
* Is the A/V ratio based on the internal or the external dimensions?
* How is the exterior climate data interpolated with shorter timesteps than available in the climate file? How big is the difference of simulations with hourly values and shorter timesteps?
* How are the ventilation control mechanisms exactly?
* How do I model groundwater? (I can only specify 100% RH but no fluid water on the surface)

=== Wishlist ===

* Time-dependent shading
* Specified saving options (without results, with general results, with results for each component) on one page, not seperately for each component
* Calculation results: Please add surface area in the component information part
* Differentiation between forced and natural air exchange (with possibility to read file)
* Preview of the created building in the building wizard
* Define standard dimensions of windows with frame reduction factor and adapt frame reduction factor with changing window dimensions
* Start "Calc Wufi" from header-dialog
* Delete "new case" button
* Give choice if one wants to copy windows for every storey in a multi-storey building
* Batch mode for WUFI Plus with automatic results file generation
* Possibility to read each boundary condition from file
* Save project without results

=== Christoph's annotation ===
==== Smaller Problems ====
* ''' Distribution of solar gains on inner surfaces'''

If ''Other_Parameters'' "Proportional to area", 100% of solar gains will distributed proportional to the components, or 100% less "Solar radiation direct to inner Air"?

In the case of "Proportional to area" in ''Components -> Numerics'' "Solar radiation on inner surfaces[%]" shows the percentage [1...100] in an inactive box. But if "user defined" you must not input a number between [1...100], but between [0...1].

Discussion:Main

2008-08-07T05:06:53Z

Cmitterer: /* Christoph's annotation */

Please make sure, that the user is '''NOT''' the problem. After that proceed with the following:

== WUFI 1D Pro ==

hmm...

== WUFI 2D ==

haa...

== WUFI-Plus ==

=== Bugs ===
* Two graphs are shown on one page. If the date-axis is changed on the above graph, the second graph is then different - but only one x-axis label is available.
* Sometimes window can not be minimized

=== Problems ===

* By use of "Assign from Database" the setup is overridden without asking (asking happens only if "Edit" is used.
* How do I create a monopitch roof?
* Is the A/V ratio based on the internal or the external dimensions?
* How is the exterior climate data interpolated with shorter timesteps than available in the climate file? How big is the difference of simulations with hourly values and shorter timesteps?
* How are the ventilation control mechanisms exactly?
* How do I model groundwater? (I can only specify 100% RH but no fluid water on the surface)

=== Wishlist ===

* Time-dependent shading
* Specified saving options (without results, with general results, with results for each component) on one page, not seperately for each component
* Calculation results: Please add surface area in the component information part
* Differentiation between forced and natural air exchange (with possibility to read file)
* Preview of the created building in the building wizard
* Define standard dimensions of windows with frame reduction factor and adapt frame reduction factor with changing window dimensions
* Start "Calc Wufi" from header-dialog
* Delete "new case" button
* Give choice if one wants to copy windows for every storey in a multi-storey building
* Batch mode for WUFI Plus with automatic results file generation
* Possibility to read each boundary condition from file
* Save project without results

=== Christoph's annotation ===
==== Smaller Problems ====
* ''' Distribution of solar gains on inner surfaces'''
If ''Other_Parameters'' "Proportional to area" 100% of solar gains will distributed proportional to the components, or 100% less "Solar radiation direct to inner Air"? In the case of "Proportional to area" in ''Components -> Numerics'' "Solar radiation on inner surfaces[%]" shows the percentage [1...100] in an inactive box. But if "user defined" you must not input a number between [1...100], but between [0...1].

Discussion:Main

2008-08-07T04:35:31Z

Cmitterer:

Datei:Screenshot - 07.08.2008 , 12 24 00.png

2008-08-07T04:31:30Z

Cmitterer:

Discussion:Main

2008-08-07T03:53:38Z

Cmitterer: /* Wishlist */

Discussion:Main

2008-08-07T03:52:51Z

Cmitterer:

Benutzer Diskussion:Cmitterer

2008-04-14T09:12:07Z

Cmitterer: hat „Benutzer Diskussion:Cmitterer“ nach „Problems and Bugs“ verschoben

#REDIRECT [[Problems and Bugs]]

Problems and Bugs

2008-04-14T09:12:07Z

Cmitterer: hat „Benutzer Diskussion:Cmitterer“ nach „Problems and Bugs“ verschoben

wo erscheint das?

Problems and Bugs

2008-04-14T09:09:35Z

Cmitterer: Die Seite wurde neu angelegt: wo erscheint das?

wo erscheint das?