Plus 2.X:Building Wizard - Versionsgeschichte

Krizzl: /* Other Options */

2011-04-28T11:05:39Z

Other Options

← Nächstältere Version		Version vom 28. April 2011, 13:05 Uhr
Zeile 48:		Zeile 48:
	'''"Group Components"''': There is a Possibility to automatically group similar components, for example exterior walls. They are seen as one component then so for example not each single part of the exterior wall needs to be assigned with an assembly in particular. Ungrouping components is possible in the [[Plus 2.X:Building#Component Operations\|Visualization Box]]		'''"Group Components"''': There is a Possibility to automatically group similar components, for example exterior walls. They are seen as one component then so for example not each single part of the exterior wall needs to be assigned with an assembly in particular. Ungrouping components is possible in the [[Plus 2.X:Building#Component Operations\|Visualization Box]]

	'''"Divide into Stories"''': If the Building has got more than one story you can decide whether each story should have its "own" components (set the check mark) or ~~weather~~ the components shouldn't be parted (remove check mark).		'''"Divide into Stories"''': If the Building has got more than one story you can decide whether each story should have its "own" components (set the check mark) or whether the components shouldn't be parted (remove check mark).

Krizzl: /* Other Options */

2011-04-28T11:03:19Z

Other Options

← Nächstältere Version		Version vom 28. April 2011, 13:03 Uhr
Zeile 48:		Zeile 48:
	'''"Group Components"''': There is a Possibility to automatically group similar components, for example exterior walls. They are seen as one component then so for example not each single part of the exterior wall needs to be assigned with an assembly in particular. Ungrouping components is possible in the [[Plus 2.X:Building#Component Operations\|Visualization Box]]		'''"Group Components"''': There is a Possibility to automatically group similar components, for example exterior walls. They are seen as one component then so for example not each single part of the exterior wall needs to be assigned with an assembly in particular. Ungrouping components is possible in the [[Plus 2.X:Building#Component Operations\|Visualization Box]]

	'''"Divide into Stories"''': If the Building has got more than one story you can decide ~~weather~~ each story should have its "own" components (set the check mark) or weather the components shouldn't be parted (remove check mark).		'''"Divide into Stories"''': If the Building has got more than one story you can decide whether each story should have its "own" components (set the check mark) or weather the components shouldn't be parted (remove check mark).

Krizzl: /* Other Options */

2011-04-27T12:30:42Z

Other Options

← Nächstältere Version		Version vom 27. April 2011, 14:30 Uhr
Zeile 45:		Zeile 45:

	On the right side there are two other options: <br>		On the right side there are two other options: <br>

	'''"Group Components"''': There is a Possibility to automatically group similar components, for example exterior walls. They are seen as one component then so for example not each single part of the exterior wall needs to be assigned with an assembly in particular. Ungrouping components is possible in the [[Plus 2.X:Building#Component Operations\|Visualization Box]]		'''"Group Components"''': There is a Possibility to automatically group similar components, for example exterior walls. They are seen as one component then so for example not each single part of the exterior wall needs to be assigned with an assembly in particular. Ungrouping components is possible in the [[Plus 2.X:Building#Component Operations\|Visualization Box]]

			'''"Divide into Stories"''': If the Building has got more than one story you can decide weather each story should have its "own" components (set the check mark) or weather the components shouldn't be parted (remove check mark).
	'''"Divide into Stories"''': If the Building has got more than one story you can decide weather each story should have its "own" components (set the check mark) or weather the components shouldn't be parted (remove check mark).

Krizzl am 27. April 2011 um 12:30 Uhr

2011-04-27T12:30:20Z

← Nächstältere Version		Version vom 27. April 2011, 14:30 Uhr
Zeile 1:		Zeile 1:
	= Building =		== Building ==

	The most important part of WUFI-Plus is the option to create a building.		The most important part of WUFI-Plus is the option to create a building.
Zeile 11:		Zeile 11:
	[[Bild:P2-Building_Wizard.png]]		[[Bild:P2-Building_Wizard.png]]

	With the automatic building wizard three essential points of a building can be defined, the footprint, the roof and the bottom offset. First of all you have to choose one of the proposed '''Main section''', '''Roof'''or '''Bottom offset''' . After this you can define the dimensions of the building. The yellow parts of the building are the heated zone and the white parts are unheated zones.

	~~Below~~ the ~~selection graphs, given measures can be specified. These vary with the choice of footprint, roof or bottom offset.~~		===Defining the Geometry===

	~~After defining these~~ the ~~storey height and the number~~ of ~~stories~~ can be defined on the ~~left bottom side of~~ the ~~dialog. On~~ the bottom ~~side~~ of ~~the dialog the orientation~~ of the ~~main facade needs to be defined~~. The ~~main facade depends on~~ the ~~footprint of~~ the ~~building~~ and ~~is shown in~~ the ~~selection graph for the footprint selection~~.		With the automatic building wizard three essential points of a building can be defined, the footprint, the roof and the bottom offset. First of all you have to choose one of the proposed '''Main section''', '''Roof''' and '''Bottom offset'''. The yellow parts in the illustrations are the heated zone and the white parts are unheated zones.

			After this you can define the dimensions of the building. Below the selection graphs, given measures can be specified. These vary with the choice of footprint, roof and bottom offset. Also under '''Main section''' the story height and the number of stories can be defined. Under '''Roof''' there is the possibility to check mark the entry "Gable ends" for a gable roof.

	~~=== Footprint Selection ===~~

	~~[[image:SelectionFootprint.png\|thumb\|left\|Different choosable footprints]]~~
	~~These footprints can actually be choosen in the Building Wizard.~~

	~~<br style="clear:both" />~~		On the bottom side of the dialog the orientation of the main facade needs to be defined either by means of main orientations or by Azimuth. The main facade depends on the footprint of the building and is shown in the selection graph for the footprint selection.
	~~=== Roof Selection ===~~

	[[image:SelectionRoof.png\|thumb\|left\|Different choosable roofs]]		This is a overview over the possibilities the Building Wizard offers:
	~~These roofs can actually be choosen in the Building Wizard~~.		{\|
			\|'''Footprint Selection'''
			\|
			\|'''Roof Selection'''
			\|
			\|'''Bottom Offset Selection'''
			\|-
			\|[[image:SelectionFootprint.png\|thumb\|left\|Different choosable footprints]]
			\|
			\|[[image:SelectionRoof.png\|thumb\|left\|Different choosable roofs]]
			\|
			\|[[image:SelectionBottom.png\|thumb\|left\|Different choosable bottom offsets]]
			\|}

	~~<br style~~=~~"clear:both" />~~		===Defining the Orientation===
	==~~= Bottom Offset Selection~~ ===

	~~[[image:SelectionBottom.png\|thumb\|left\|Different choosable~~ bottom ~~offsets]]~~		On the bottom side of the dialog the orientation of the main facade needs to be defined either by means of main orientations or by Azimuth. The main facade depends on the footprint of the building and is shown in the selection graph for the footprint selection.
	~~These bottom offsets can actually~~ be ~~choosen~~ in the ~~Building Wizard~~.

	~~<br style="clear:both" />~~

			===Other Options===

	On the ~~bottom~~ side of the ~~dialog the orientation of the main facade~~ needs to be ~~defined~~. ~~The main facade depends on the footprint of the building and~~ is ~~shown~~ in the ~~selection graph for the footprint selection~~.		On the right side there are two other options: <br>
			'''"Group Components"''': There is a Possibility to automatically group similar components, for example exterior walls. They are seen as one component then so for example not each single part of the exterior wall needs to be assigned with an assembly in particular. Ungrouping components is possible in the [[Plus 2.X:Building#Component Operations\|Visualization Box]]

	~~On the right side there are two options: "Group Components" and "Divide into Stories"~~

	(.~~..)~~		'''"Divide into Stories"''': If the Building has got more than one story you can decide weather each story should have its "own" components (set the check mark) or weather the components shouldn't be parted (remove check mark).

Krizzl: /* Building */

2011-04-27T11:21:12Z

Building

← Nächstältere Version		Version vom 27. April 2011, 13:21 Uhr
Zeile 3:		Zeile 3:
	The most important part of WUFI-Plus is the option to create a building.		The most important part of WUFI-Plus is the option to create a building.

	The design of the building can be created in two ways. The easier way is to use the automatic building wizard. With this tool it is possible to design simple footprints and typical roof and cellar constructions. When the footprint and building construction is more complicated as the available samples there is the possibility to design the building using vertices. Also it is possible to create a simple building using the Building wizard and then to expand it using vertices.		The design of the building can be created in two ways. The easier way is to use the automatic building wizard. With this tool it is possible to design simple footprints and typical roof and cellar constructions. When the footprint and building construction is more complicated as the available samples there is the possibility to design the building using vertices. Also it is possible to create a simple building using the Building wizard and then to expand it using [[Plus 2.X:Building#Edit 3D\|vertices.]]

	== Automatic building wizard ==		== Automatic building wizard ==

Krizzl: /* Building */

2011-04-27T11:20:29Z

Building

← Nächstältere Version		Version vom 27. April 2011, 13:20 Uhr
Zeile 3:		Zeile 3:
	The most important part of WUFI-Plus is the option to create a building.		The most important part of WUFI-Plus is the option to create a building.

	The design of the building can ~~create by~~ two ways. The easier way is to use the automatic building wizard. With this tool it is possible to design simple footprints and typical roof and cellar constructions. When the footprint and building construction is more complicated as the available samples there is the possibility to design the building using vertices.		The design of the building can be created in two ways. The easier way is to use the automatic building wizard. With this tool it is possible to design simple footprints and typical roof and cellar constructions. When the footprint and building construction is more complicated as the available samples there is the possibility to design the building using vertices. Also it is possible to create a simple building using the Building wizard and then to expand it using vertices.

	== Automatic building wizard ==		== Automatic building wizard ==

Krizzl: Die Seite wurde neu angelegt: = Building = The most important part of WUFI-Plus is the option to create a building. The design of the building can create by two ways. The easier way is to use the ...

2011-04-26T10:34:15Z

Die Seite wurde neu angelegt: = Building = The most important part of WUFI-Plus is the option to create a building. The design of the building can create by two ways. The easier way is to use the ...

Neue Seite

= Building =

The most important part of WUFI-Plus is the option to create a building.

The design of the building can create by two ways. The easier way is to use the automatic building wizard. With this tool it is possible to design simple footprints and typical roof and cellar constructions. When the footprint and building construction is more complicated as the available samples there is the possibility to design the building using vertices.

== Automatic building wizard ==

The '''Building Wizard''' is a tool to design a house for the simulation.

[[Bild:P2-Building_Wizard.png]]

With the automatic building wizard three essential points of a building can be defined, the footprint, the roof and the bottom offset. First of all you have to choose one of the proposed '''Main section''', '''Roof'''or '''Bottom offset''' . After this you can define the dimensions of the building. The yellow parts of the building are the heated zone and the white parts are unheated zones.

Below the selection graphs, given measures can be specified. These vary with the choice of footprint, roof or bottom offset.

After defining these the storey height and the number of stories can be defined on the left bottom side of the dialog. On the bottom side of the dialog the orientation of the main facade needs to be defined. The main facade depends on the footprint of the building and is shown in the selection graph for the footprint selection.

=== Footprint Selection ===

[[image:SelectionFootprint.png|thumb|left|Different choosable footprints]]
These footprints can actually be choosen in the Building Wizard.

<br style="clear:both" />
=== Roof Selection ===

[[image:SelectionRoof.png|thumb|left|Different choosable roofs]]
These roofs can actually be choosen in the Building Wizard.

<br style="clear:both" />
=== Bottom Offset Selection ===

[[image:SelectionBottom.png|thumb|left|Different choosable bottom offsets]]
These bottom offsets can actually be choosen in the Building Wizard.

<br style="clear:both" />

On the bottom side of the dialog the orientation of the main facade needs to be defined. The main facade depends on the footprint of the building and is shown in the selection graph for the footprint selection.

On the right side there are two options: "Group Components" and "Divide into Stories"

(...)